Comments on: Small Business PBX made easy

By: Nitant Mohan

Nitant Mohan — Fri, 02 Dec 2011 13:18:53 +0000

can same one let me know ,i have connected Mypbx system with Injector Hub and switch and UPS ,but problem is when we have Power Failure all system went down ,so what to do even there is no power atleast all the telephone will work….please help to find the Solution.

By: Jaco

Jaco — Mon, 13 Jun 2011 07:47:44 +0000

Is it possible to connect an overhead PA to the MyPBX and how?

By: inam hasan mih13athotmail

inam hasan mih13athotmail — Thu, 21 Apr 2011 23:00:28 +0000

HI Imel,

I have MyPbx V3 and need to configure skype out to call skype users from my sip base extension. Any idea please.

Regadrs

iNAM

By: imel

imel — Tue, 01 Mar 2011 08:38:08 +0000

Hi Allan, not sure who in Cape town could assist you. I would suggest asking Abby at Scoop whom they would suggest.
Also note that there is now a newer model of the MyPBX out that supports ISDN and GSM connections as well.
See here

Regards
Imel

By: Allan Whatley

Allan Whatley — Mon, 28 Feb 2011 15:58:33 +0000

Hi Imel

I was very interested in your article on the MyPBX installation. We’re interested in supplying one of these to a client. Do you know anyone in Cape Town that can set up the MyBPX for us?

It’s a hybrid environment, mostly analog migrating to IP later. It will sit infront of a gateway connected into a a VOIP service.

Thanks

Allan

By: Steve Caveney

Steve Caveney — Mon, 13 Sep 2010 15:41:48 +0000

Hi Imel,

As per a previous post, I am going to add to this WRT outgoing calls on SIP trunks. I have now done 2 installations with one Standard and one SOHO MyPBX. On both sites, I cannot get SIP working outbound. Inbound fine, PBX reports trunk registered but I also get the “all circuits are busy” error. On both Sites I have implemented Atcom 620P handsets that have a second SIP account, when I use this and enter the SIP details directly , thereby bypassing the PBX, the trunk works fine so this rules out firewall issues. No sure if the Atcom is using UPNP to dynamically open F/W ports, however when putting the mypbx on a DMZ it still does not work

Any help appreciated

By: Chris Lee

Chris Lee — Wed, 12 May 2010 10:31:16 +0000

Hi Imel,

Hope you can help? I am having a similar problem to Otto and searching the internet pretty much brings up your site all the time.

I can however dial out. Just not to a VOIP Trunk I have setup for to use skype. I keep on getting the same error about “all circuits are busy now”

Using skype I have linked an account and an online number. When “dialling” the account name via skype. myPBX redirects the calls perfectly. However when dialling the new online number i have bought. It just gets a busy tone. From the skype log it seems as if the number is reaching myPBX and then dropping?

Do you have any advice, or perhaps know who I can phone in Gauteng?

By: Otto

Otto — Sun, 18 Apr 2010 06:34:13 +0000

Hi Imel

I recently purchased a MyPBX SOHO from Scoop. After setup and with both VoIP lines registered with my provider (Telfree) I can phone extensions OK and get incoming calls OK. I’m having trouble making outbound calls though – It keeps on telling me “all circuits are busy now”.

I am using the G.729 CODEC as required by Telfree. That specific CODEC is not included (licensed) with the SOHO edition but I have bought one some time ago and installed it on the SOHO

I’m fairly new to VoIP and any help will be appreciated

By: imel

imel — Tue, 23 Mar 2010 20:45:21 +0000

Yes, SIP handsets on the same LAN logs into the MyPBX to gain the functionality of the PBX.

By: imel

imel — Tue, 23 Mar 2010 20:43:59 +0000

Hi Simon, give Connection Telecom in Cape Town a try, speak to Steve or Rob.
Their voip gateway is great and reliable.